Не получается разбить потоки на группы, проблема в том что в каждой группе работает только один поток.

Не получается разбить потоки на группы, проблема в том что в каждой группе работает только один поток. Не могу понять почему. Прежде чем писать прочел форум почитал гугл, вот что из этого получилось. Вобщем всё настроено в dahdi-channels.conf Прошу помощи или дайте ссылочку где почитать. Спасибо!

[channels] overlapdial=no priindication=outofband toneduration=600 usecallerid=yes callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes rxgain=-5.0 txgain=0.0 resetinterval=100000000 ; ;[trunk_g1] ;group=1 ;switchtype=qsig ;context=trunk_g1 ;pridialplan=unknown ;signalling=pri_net ;immediate=no ;dahdichan=1-15,17-31,32-46,48-62 ; ;[trunk_g2] ;group=2 ;switchtype=euroisdn ;pridialplan=unknown ;context=trunk_g2 ;signalling=pri_cpe ;immediate=no ;dahdichan=63-77,79-93 ; ;[trunk_g3] ;group=3 ;switchtype=euroisdn ;pridialplan=unknown ;context=trunk_g3 ;signalling=pri_net ;immediate=no ;;dahdichan=125-139,141-155,156-170,172-186,187-201,203-217,218-232,234-248 ;dahdichan=187-201,203-217,218-232,234-248

; Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS group = 1 context = trunk_g1 switchtype = qsig signalling = pri_net channel => 1-15,17-31 context = trunk_g1 group =

; Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS group = 1 context = trunk_g1 switchtype = qsig signalling = pri_net channel => 32-46,48-62 context = trunk_g1 group =

; Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" HDB3/CCS group = 2 context = trunk_g2 switchtype = euroisdn signalling = pri_cpe channel => 63-77,79-93 context = trunk_g2 group =

; Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" HDB3/CCS group = 2 context = trunk_g2 switchtype = euroisdn signalling = pri_cpe channel => 94-108,110-124 context = trunk_g2 group =

; Span 5: TE4/1/1 "T4XXP (PCI) Card 1 Span 1" HDB3/CCS RED ;group = 2 ;context = trunk_g2 ;switchtype = euroisdn ;signalling = pri_cpe ;channel => 125-139,141-155 ;context = trunk_g2 ;group =

; Span 6: TE4/1/2 "T4XXP (PCI) Card 1 Span 2" HDB3/CCS RED ;group = 3 ;context = trunk_g3 ;switchtype = euroisdn ;signalling = pri_net ;channel => 156-170,172-186 ;context = trunk_g3 ;group =

; Span 7: TE4/1/3 "T4XXP (PCI) Card 1 Span 3" HDB3/CCS group = 3 context = trunk_g3 switchtype = euroisdn signalling = pri_net channel => 187-201,203-217 context = trunk_g3 group =

; Span 8: TE4/1/4 "T4XXP (PCI) Card 1 Span 4" HDB3/CCS group = 3 context = trunk_g3 switchtype = euroisdn signalling = pri_net channel => 218-232,234-248 context = trunk_g3 group =

Re: Не получается разбить потоки на группы, проблема в том что в каждой группе работает только один поток.

; ;[trunk_g1] ;group=1 ;switchtype=qsig ;context=trunk_g1 ;pridialplan=unknown ;signalling=pri_net ;immediate=no ;dahdichan=1-15,17-31,32-46,48-62 ; ;[trunk_g2] ;group=2 ;switchtype=euroisdn ;pridialplan=unknown ;context=trunk_g2 ;signalling=pri_cpe ;immediate=no ;dahdichan=63-77,79-93 ; ;[trunk_g3] ;group=3 ;switchtype=euroisdn ;pridialplan=unknown ;context=trunk_g3 ;signalling=pri_net ;immediate=no ;;dahdichan=125-139,141-155,156-170,172-186,187-201,203-217,218-232,234-248 ;dahdichan=187-201,203-217,218-232,234-248

; Span 5: TE4/1/1 "T4XXP (PCI) Card 1 Span 1" HDB3/CCS RED ;group = 2 ;context = trunk_g2 ;switchtype = euroisdn ;signalling = pri_cpe ;channel => 125-139,141-155 ;context = trunk_g2 ;group =

; Span 6: TE4/1/2 "T4XXP (PCI) Card 1 Span 2" HDB3/CCS RED ;group = 3 ;context = trunk_g3 ;switchtype = euroisdn ;signalling = pri_net ;channel => 156-170,172-186 ;context = trunk_g3 ;group =

Re: Не получается разбить потоки на группы, проблема в том что в каждой группе работает только один поток.

Соласен. Исправляюсь. Вот что "работает", точнее работает ровно на 50% в каждой группе только один поток.

; Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS group = 1 context = trunk_g1 switchtype = qsig signalling = pri_net channel => 1-15,17-31 context = trunk_g1 group =

; Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS group = 1 context = trunk_g1 switchtype = qsig signalling = pri_net channel => 32-46,48-62 context = trunk_g1 group =

; Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" HDB3/CCS group = 2 context = trunk_g2 switchtype = euroisdn signalling = pri_cpe channel => 63-77,79-93 context = trunk_g2 group =

; Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" HDB3/CCS group = 2 context = trunk_g2 switchtype = euroisdn signalling = pri_cpe channel => 94-108,110-124 context = trunk_g2 group =

; Span 7: TE4/1/3 "T4XXP (PCI) Card 1 Span 3" HDB3/CCS group = 3 context = trunk_g3 switchtype = euroisdn signalling = pri_net channel => 187-201,203-217 context = trunk_g3 group =

; Span 8: TE4/1/4 "T4XXP (PCI) Card 1 Span 4" HDB3/CCS group = 3 context = trunk_g3 switchtype = euroisdn signalling = pri_net channel => 218-232,234-248 context = trunk_g3 group =

Re: Не получается разбить потоки на группы, проблема в том что в каждой группе работает только один поток.

На карточках индикация: 1,2,3,4,7,8 Зелёные 5,6 Красные (они не используются в них ничего не воткнуто).

dahdi_tool говорит: Alarm Span 1,2,3,4,7,8 OK Alarm Span 5,6 Red

dahdi_cfg -vv говорит: 248 channels to configure Далее вывод строк о включении эходава: Setting echocan for channel 1 to mg2 - для каждого канала по 248-й включительно кроме служебных каналов 16,47,78,109,140,171,202,233 для них строки такого типа: Setting echocan for channel 16 to none

Re: Не получается разбить потоки на группы, проблема в том что в каждой группе работает только один поток.

Попробовал искуственно создать ситуацию со звонком в город через не используемый поток. Звонок состоялся. В город смотрит группа№2 это Span3 и Span4. При вызовах на группу, звонки уходят только через Span4. Взял 63-й канал из Span3 и включил pri debug на Span3.

План набора (использую AEL): 1234567 => < Verbose(------------EXPERIMENTAL CALL-------------); Dial(DAHDI/63/100); Hangup; >

DEBUG: ------------EXPERIMENTAL CALL------------- -- Executing [1234567@trunk_g3:2] Dial("DAHDI/187-1", "DAHDI/63/100") in new stack -- Making new call for cref 32774 -- Requested transfer capability: 0x00 - SPEECH > Protocol Discriminator: Q.931 (8) len=33 > TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent from originator) > Message Type: SETUP (5) > [04 03 80 90 a3] > Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: Speech (0) > Ext: 1 Trans mode/rate: 64kbps, circuit-mode (16) > User information layer 1: A-Law (35) > [18 03 a1 83 81] > Channel ID (len= 5) [ Ext: 1 IntID: Implicit Other(PRI) Spare: 0 Preferred Dchan: 0 > ChanSel: As indicated in following octets > Ext: 1 Coding: 0 Number Specified Channel Type: 3 > Ext: 1 Channel: 1 Type: CPE] > [6c 09 21 83 34 39 35 32 30 30 30] > Calling Number (len=11) [ Ext: 0 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan (E.164/E.163) (1) > Presentation: Presentation allowed of network provided number (3) '4952000' ] > [70 04 80 31 30 30] > Called Number (len= 6) [ Ext: 1 TON: Unknown Number Type (0) NPI: Unknown Number Plan (0) '100' ] > [a1] > Sending Complete (len= 1) q931.c:4877 q931_setup: Call 32774 enters state 1 (Call Initiated). Hold state: Idle -- Called 63/100 < Protocol Discriminator: Q.931 (8) len=10 < TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent to originator) < Message Type: CALL PROCEEDING (2) < [18 03 a9 83 81] < Channel ID (len= 5) [ Ext: 1 IntID: Implicit Other(PRI) Spare: 0 Exclusive Dchan: 0 < ChanSel: As indicated in following octets < Ext: 1 Coding: 0 Number Specified Channel Type: 3 < Ext: 1 Channel: 1 Type: CPE] Received message for call 0xa420e98 on 0x90b8f68 TEI/SAPI 0/0, call->pri is 0x90b8f68 TEI/SAPI 0/0 -- Processing IE 24 (cs0, Channel Identification) q931.c:6916 post_handle_q931_message: Call 32774 enters state 3 (Outgoing Call Proceeding). Hold state: Idle -- DAHDI/63-1 is proceeding passing it to DAHDI/187-1 < Protocol Discriminator: Q.931 (8) len=9 < TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent to originator) < Message Type: PROGRESS (3) < [1e 02 82 88] < Progress Indicator (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Public network serving the local user (2) < Ext: 1 Progress Description: Inband information or appropriate pattern now available. (8) ] Received message for call 0xa420e98 on 0x90b8f68 TEI/SAPI 0/0, call->pri is 0x90b8f68 TEI/SAPI 0/0 -- Processing IE 30 (cs0, Progress Indicator) -- DAHDI/63-1 is making progress passing it to DAHDI/187-1 -- DAHDI/63-1 is making progress passing it to DAHDI/187-1 < Protocol Discriminator: Q.931 (8) len=9 < TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent to originator) < Message Type: PROGRESS (3) < [1e 02 82 88] < Progress Indicator (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Public network serving the local user (2) < Ext: 1 Progress Description: Inband information or appropriate pattern now available. (8) ] Received message for call 0xa420e98 on 0x90b8f68 TEI/SAPI 0/0, call->pri is 0x90b8f68 TEI/SAPI 0/0 -- Processing IE 30 (cs0, Progress Indicator) -- DAHDI/63-1 is making progress passing it to DAHDI/187-1 -- DAHDI/63-1 is making progress passing it to DAHDI/187-1 < Protocol Discriminator: Q.931 (8) len=5 < TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent to originator) < Message Type: CONNECT (7) Received message for call 0xa420e98 on 0x90b8f68 TEI/SAPI 0/0, call->pri is 0x90b8f68 TEI/SAPI 0/0 q931.c:6837 post_handle_q931_message: Call 32774 enters state 10 (Active). Hold state: Idle > Protocol Discriminator: Q.931 (8) len=5 > TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent from originator) > Message Type: CONNECT ACKNOWLEDGE (15) -- DAHDI/63-1 answered DAHDI/187-1

< Protocol Discriminator: Q.931 (8) len=9 < TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent to originator) < Message Type: DISCONNECT (69) < [08 02 8f 90] < Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: Unknown (15) < Ext: 1 Cause: Normal Clearing (16), Event (1) ] Received message for call 0xa420e98 on 0x90b8f68 TEI/SAPI 0/0, call->pri is 0x90b8f68 TEI/SAPI 0/0 -- Processing IE 8 (cs0, Cause) -- Found active call: 0xa420e98 cref:32774 q931.c:7119 post_handle_q931_message: Call 32774 enters state 12 (Disconnect Indication). Hold state: Idle

q931_hangup: other hangup NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Disconnect Indication, peerstate Disconnect Request, hold-state Idle q931.c:4639 q931_release: Call 32774 enters state 19 (Release Request). Hold state: Idle > Protocol Discriminator: Q.931 (8) len=9 > TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent from originator) > Message Type: RELEASE (77) > [08 02 81 90] > Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: Private network serving the local user (1) > Ext: 1 Cause: Normal Clearing (16), Event (1) ] -- Hungup 'DAHDI/63-1' == Spawn extension (trunk_g3, 1234567, 2) exited non-zero on 'DAHDI/187-1' -- Hungup 'DAHDI/187-1' < Protocol Discriminator: Q.931 (8) len=5 < TEI=0 Call Ref: len= 2 (reference 6/0x6) (Sent to originator) < Message Type: RELEASE COMPLETE (90) Received message for call 0xa420e98 on 0x90b8f68 TEI/SAPI 0/0, call->pri is 0x90b8f68 TEI/SAPI 0/0 q931.c:7001 post_handle_q931_message: Call 32774 enters state 0 (Null). Hold state: Idle q931_hangup: other hangup NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Null, hold-state Idle NEW_HANGUP DEBUG: Destroying the call, ourstate Null, peerstate Null, hold-state Idle

📎📎📎📎📎📎📎📎📎📎